EQ #	NAME	HP	"3 O
VOLTS"	"F.L.
AMPS"	"SAFETY
SW & SIZE"	FUSE	"WIRE
SIZE"	"GROUND
SIZE"	"CONDUIT
SIZE"	PNL #	CKT #	"BRKR
SIZE"	"FUSE
SIZE"
1	Rip Saw	30	460	40	60	60	3 #8	10	"1"""	DSL-1	"1,3,5"	--	60
2	Wienig Moulder	Vari	460	95	100	100	3 #2	8	"1 1/4"""	DSL-1	"2,4,6"	--	100
3	Ramco Sander	25	460	34	60	60	3 #8	10	"1"""	DSL-1	"8,10,12"	--	60
4	"36"" Bandsaw"	10	460	14	30	30	3 #12	12	"3/4"""	DSL-1	"7,9,11"	--	20
5	Jointer	3	460	9.5	30	10	3 #12	10	"3/4"""	DSL-1	"13,15,17"	--	10
6	Rockwell Planer	5	460	7.6	30	10	3 #12	10	"3/4"""	DSL-1	"14,16,18"	--	60
7	Pneumatic Table Saw	20	230	54	100	70	3 #6	8	"1"""	PPA	"2,4,6"	--	70
8	Shaper	30	230	80	100	100	3 #4	8	"1 1/4"""	PPA	"1,3,5"	--	100
9	Seco Shaper	5	230	15	30	20	CORD	&	PLUG	PPA	"7,9,11"	--	20
10	Seco Table Shaper	5	230	15	30	20	CORD	&	PLUG	PPA	"8,10,12"	--	20
11	Mitre Saw	5	230	15	30	20	3 #10	12	"3/4"""	PPA	"14,16,18"	--	20
12	Radial Arm Saw	3	230	9.6	30	15	3 #10	12	"3/4"""	PPA	"13,15,17"	--	15
13	Whirlwind Cut Off Saw	5	230	15	30	20	3 #10	12	"3/4"""	PPA	"20,22,24"	--	20
14	Powermatic Table Saw	5	230	15	30	20	3 #10	12	"3/4"""				20
15	Panel Saw	3	230	12.2	30	20	3 #10	12	"3/4"""				20
16	Edge Bender	Vari	230	27.7	30	30	3 #10	12	"3/4"""				30
17	Table Saw	5	230	15	30	30	3 #10	12	"3/4"""				30
18	Dado Saw	3	230	9.6	30	30	3 #10	12	"3/4"""				20
19	Boring Mach	3	230	9.6	30	30	3 #10	12	"3/4"""				20
20	Boring Mach	3	230	9.6	30	30	3 #10	12	"3/4"""				20
21	Boring Mach	3	230	9.6	30	30	CORD	&	PLUG				20
22	Boring Mach	1	230	3.5	30	10	CORD	&	PLUG				10
23	Table Saw	5	230	15	30	30	CORD	&	PLUG				30
24	Spray Booth	---	230	13.2	30	20	3 #10	12	"3/4"""				20
24A	Spray Booth	---	230	13.2	30	20	3 #10	12	"3/4"""				20
25	Spray Booth	7.5	230	22	30	30	3 #10	12	"3/4"""				30
26	Air Comp	25	230	64	100	100	3 #4	8	"1 1/4"""				100
27	Drill		230	3.1	30	15	CORD	&	PLUG				15
28	Groover		230	7.5	30	15	CORD	&	PLUG				15
29	Horizontal Drill	1.5	230	4.6	30	15	CORD	&	PLUG				15
30	Sander	3	230	8.4	30	15	CORD	&	PLUG				
31	Miter Saw	2	230	6.8	30	15	3 #12	12					
32	Sander	2	230	6.6									
33	Dust Col.	60	460	77	100	100	3 #4	8	"1"""				100
34	Saw	---	230	80	100	100	3 #3	8	"1 1/4"""				100
35	CNC Mach	---	230	63	100	100	3 #6	8	"3/4"""				100


"NOTE:  THE ABOVE HARD WIRED EQUIPMENT SHALL BE RELOCATED WITH SAFETY SWITCH,"													
"FUSES, ""SO"" CORD DROP, ETC.  EQUIPMENT ITEMS WITH CORD & PLUG SHALL BE"													
RELOCATED WITH THE EQUIPMENT.  ASSURE THAT ALL HARD WIRED EQUIPMENT HAS A													
SAFETY SWITCH AND THAT SWITCH IS RATED OR GREATER THAN CIRCUIT VOLTAGE.