USACE / NAVFAC / AFCESA / NASA UFGS-23 08 00.00 10 (January 2008)
----------------------------------
Preparing Activity: USACE Superseding
UFGS-23 08 00.00 10 (April 2006)
UNIFIED FACILITIES GUIDE SPECIFICATIONS
References are in agreement with UMRL dated January 2009
SECTION 23 08 00.00 10
COMMISSIONING OF HVAC SYSTEMS
01/08
NOTE: This guide specification covers the requirements for commissioning of
HVAC systems.
Edit this guide specification for project specific requirements by adding, deleting,
or revising text. For bracketed items, choose applicable items(s) or insert
appropriate information.
Remove information and requirements not required in respective project, whether
or not brackets are present.
Comments and suggestions on this guide specification are welcome and should
be directed to the technical proponent of the specification. A listing of technical
proponents, including their organization designation and telephone number, is
on the Internet.
Recommended changes to a UFGS should be submitted as a Criteria Change Request
(CCR).
PART 1 GENERAL
NOTE: Use of this specification is mandatory for all projects. A properly
functioning HVAC system assures a comfortable, healthy and productive environment
for the user. The "Design Agent's Representative" will be a member of the HVAC
design team, i.e. from the AE or Engineering Division. The "Design Agent's
Representative" will actively participate in the process, including review of
all submittals contained herein.
1.1 REFERENCES
NOTE: This paragraph is used to list the publications cited in the text of
the guide specification. The publications are referred to in the text by basic
designation only and listed in this paragraph by organization, designation,
date, and title.
Use the Reference Wizard's Check Reference feature when you add a RID outside
of the Section's Reference Article to automatically place the reference in the
Reference Article. Also use the Reference Wizard's Check Reference feature
to update the issue dates.
References not used in the text will automatically be deleted from this section
of the project specification when you choose to reconcile references in the
publish print process.
The publications listed below form a part of this specification to the extent referenced. The publications are
referred to within the text by the basic designation only.
[ASSOCIATED AIR BALANCE COUNCIL (AABC)ACG Commissioning Guideline(2005) Commissioning Guideline][NATIONAL ENVIRONMENTAL BALANCING BUREAU (NEBB)NEBB Commissioning Standard(1999) Procedural Standards for Building Systems Commissioning][SHEET METAL AND AIR CONDITIONING CONTRACTORS' NATIONAL ASSOCIATION (SMACNA)SMACNA 1429(1994, 1st Ed) HVAC Systems Commissioning Manual][U.S. GREEN BUILDING COUNCIL (USGBC)LEED(2002; R 2005) Leadership in Energy and Environmental Design(tm) Green Building Rating System for New Construction (LEED-NC)]1.2 DEFINITIONS
In some instances, terminology differs between the Contract and the Commissioning Standard primarily because
the intent of this Section is to use the industry standards specified, along with additional requirements listed
herein to produce optimal results. The following table of similar terms is provided for clarification only.
Contract requirements take precedent over the corresponding ACG, NEBB, or TABB requirements where differences
exist.
SIMILAR TERMS
Contract Term ACG NEBB TABB
Commissioning ACG Procedural SMACNA HVAC
Standard Commissioning Standards for Commissioning
Guideline Building Systems Guideline
Commissioning
Commissioning ACG Certified NEBB Qualified TABB Certified
Specialist Commissioning Commissioning Commissioning
Agent Administrator Supervisor
1.3 SYSTEM DESCRIPTION
1.3.1 General
Perform Commissioning in accordance with the requirements of the standard under which the Commissioning Firm's
qualifications are approved, i.e., ACG Commissioning Guideline, NEBB Commissioning Standard, or SMACNA 1429 unless
otherwise stated herein. Consider mandatory all recommendations and suggested practices contained in the Commissioning
Standard. Use the Commissioning Standard for all aspects of Commissioning, including qualifications for the
Commissioning Firm and Specialist and calibration of Commissioning instruments. Where the instrument manufacturer
calibration recommendations are more stringent than those listed in the Commissioning Standard, the manufacturer's
recommendations shall be adhered to. All quality assurance provisions of the Commissioning Standard such as
performance guarantees shall be part of this contract. For systems or system components not covered in the Commissioning
Standard, Commissioning procedures shall be developed by the Commissioning Specialist. Where new procedures,
requirements, etc., applicable to the Contract requirements have been published or adopted by the body responsible
for the Commissioning Standard used (ACG, NEBB, or TABB), the requirements and recommendations contained in these
procedures and requirements shall be considered mandatory.
1.3.2 Energy
Formal LEED certification is not required; however, the Contractor is required to provide documentation that
meets the LEED Energy & Atmosphere (EA) Prerequisite 1, Fundamental Commissioning. For New Construction
and Major Revisions provide, also, documentation that meets EA Credit 3; Enhanced Commissioning. Provide documentation
for as many LEED credits as possible to support LEED Silver certification of the project.
1.4 SUBMITTALS
NOTE: Review submittal description (SD) definitions in Section 01 33 00 SUBMITTAL
PROCEDURES and edit the following list to reflect only the submittals required
for the project. Submittals should be kept to the minimum required for adequate
quality control.
A “G” following a submittal item indicates that the submittal requires Government
approval. Some submittals are already marked with a “G”. Only delete an existing
“G” if the submittal item is not complex and can be reviewed through the Contractor’s
Quality Control system. Only add a “G” if the submittal is sufficiently important
or complex in context of the project.
For submittals requiring Government approval on Army projects, a code of up
to three characters within the submittal tags may be used following the "G"
designation to indicate the approving authority. Codes for Army projects using
the Resident Management System (RMS) are: "AE" for Architect-Engineer; "DO"
for District Office (Engineering Division or other organization in the District
Office); "AO" for Area Office; "RO" for Resident Office; and "PO" for Project
Office. Codes following the "G" typically are not used for Navy, Air Force,
and NASA projects.
Choose the first bracketed item for Navy, Air Force and NASA projects, or choose
the second bracketed item for Army projects.
Government approval is required for submittals with a "G" designation; submittals not having a "G" designation
are for [Contractor Quality Control approval.][information only. When used, a designation following the "G"
designation identifies the office that will review the submittal for the Government.] Submit the following in
accordance with Section 01 33 00 SUBMITTAL PROCEDURES:
SD-02 Shop Drawings
Commissioning Plan[; G,][;G, [_____]]
Commissioning Plan prepared in accordance with Commissioning Standard, no later than 28 days
after the approval of the Commissioning Specialist.
SD-03 Product Data
Pre-Functional Performance Test Checklists[; G,][;G, [_____]]
At least 28 days prior to the start of Pre-Functional Performance Test Checks. Submit the
schedule for the test checks at least 14 days prior to the start of Pre-Functional Performance
Test Checks.
Functional Performance Tests[; G,][;G, [_____]]
Test procedures at least 28 days prior to the start of Functional Performance Tests. The
schedule for the tests at least 14 days prior to the start of Functional Performance Tests.
SD-06 Test Reports
Commissioning Report[; G][; G, [_____]]
No later than 14 days after completion of Functional Performance Tests.
SD-07 Certificates
Commissioning Firm[; G][; G, [_____]]
Certification of the proposed Commissioning Firm's qualifications by one of the following
ACG, NEBB, or TABB to perform the duties specified herein and in other related Sections, no
later than 21 days after the Notice to Proceed. Include in the documentation the date that
the Certification was initially granted and the date when the current Certification expires.
Any lapses in Certification of the proposed Commissioning Firm or disciplinary action taken
by ACG, NEBB, or TABB against the proposed Commissioning Firm shall be described in detail.
Commissioning Specialist[; G][; G, [_____]]
Certification of the proposed Commissioning Specialist's qualifications by one of the following
ACG, NEBB, or TABB to perform the duties specified herein and in other related Sections, no
later than 21 days after the Notice to Proceed. The documentation shall include the date that
the Certification was initially granted and the date when the current Certification expires.
Any lapses in Certification of the proposed Commissioning Specialist or disciplinary action
taken by ACG, NEBB, or TABB against the proposed Commissioning Specialist shall be described
in detail.
1.5 QUALITY ASSURANCE
1.5.1 Commissioning Firm
Provide a Commissioning Firm that is either a member of ACG or certified by the NEBB or the TABB and certified
in all categories and functions where measurements or performance are specified on the plans and specifications.
The certification shall be maintained for the entire duration of duties specified herein. If, for any reason,
the firm loses subject certification during this period, immediately notify the Contracting Officer and submit
another Commissioning Firm for approval. Any firm that has been the subject of disciplinary action by the ACG,
the NEBB, or the TABB within the five years preceding Contract Award is not eligible to perform any duties related
to the HVAC systems, including Commissioning. All work specified in this Section and in other related Sections
to be performed by the Commissioning Firm shall be considered invalid if the Commissioning Firm loses its certification
prior to Contract completion and must be performed by an approved successor. These Commissioning services are
to assist the prime Contractor in performing the quality oversight for which it is responsible. The Commissioning
Firm shall be a subcontractor of the prime Contractor and shall be financially and corporately independent of
all other subContractors. The Commissioning Firm shall report to and be paid by the prime Contractor.
1.5.2 Commissioning Specialist
1.5.2.1 General
The Commissioning Specialist shall be an ACG Certified Commissioning Agent, a NEBB Qualified Commissioning Administrator,
or a TABB Certified Commissioning Supervisor and shall be an employee of the approved Commissioning Firm. The
certification shall be maintained for the entire duration of duties specified herein. If, for any reason, the
Commissioning Specialist loses subject certification during this period, immediately notify the Contracting Officer
and submit another Commissioning Specialist for approval. Any individual that has been the subject of disciplinary
action by the ACG, the NEBB, or the TABB within the five years preceding Contract Award is not eligible to perform
any duties related to the HVAC systems, including Commissioning. All work specified in this Section and in other
related Sections performed by the Commissioning Specialist shall be considered invalid if the Commissioning Specialist
loses his certification prior to Contract completion and must be performed by the approved successor.
1.5.2.2 Responsibilities
Perform all Commissioning work specified herein and in related sections under the direct guidance of the Commissioning
Specialist. The Commissioning Specialist shall prepare the Commissioning Plan, which will be a comprehensive
schedule and will include all submittal requirements for procedures, notifications, reports and the Commissioning
Report. After approval of the Commissioning Plan, revise the Contract NAS schedule to reflect the schedule requirements
in the Commissioning Plan.
1.6 SEQUENCING AND SCHEDULING
Begin the work described in this Section only after all work required in related Sections has been successfully
completed, and all test and inspection reports and operation and maintenance manuals required in these Sections
have been submitted and approved. Pre-Functional Performance Test Checklists shall be performed at appropriate
times during the construction phase of the Contract.
PART 2 PRODUCTS (Not Applicable)
PART 3 EXECUTION
3.1 COMMISSIONING TEAM AND TEST FORMS AND CHECKLISTS
NOTE: The "Design Agent's Representative" will be included as a member of the
commissioning team for the pre-commissioning checklists and will participate
in the functional performance tests.
The checklists provided are to be used as guides for the preparation of project
checklists. The appropriate checklist should be included in the project specification
for each HVAC equipment component. The designer will add additional checklists
for equipment or systems not included in this guide specification or modify
the checklists where necessary for specific project requirements. If, for example,
a system needs to be tested with certain internal load, each appropriate checklist
should be modified to include this requirement along with specifics on how load
should be generated.
Designate Contractor team members to participate in the Pre- Functional Performance Test Checklists and the Functional
Performance Tests specified herein. In addition, the Government team members will include a representative of
the Contracting Officer, the Design Agent's Representative, and the Using Agency's Representative. The team
members shall be as follows:
Designation Function
A Contractor's Commissioning Specialist
M Contractor's Mechanical Representative
E Contractor's Electrical Representative
T Contractor's Testing, Adjusting, and Balancing (TAB) Specialist
C Contractor's Controls Representative
D Design Agency Representative
O Contracting Officer's Representative
U Using Agency's Representative
Appendices A and B shall be completed by the commissioning team. Acceptance by each commissioning team member
of each Pre- Functional Performance Test Checklist item shall be indicated by initials and date unless an "X"
is shown indicating that participation by that individual is not required. Acceptance by each commissioning
team member of each functional performance test item shall be indicated by signature and date.
3.2 TESTS
Perform the pre-functional performance test checklists and functional performance tests in a manner that essentially
duplicates the checking, testing, and inspection methods established in the related Sections. Where checking,
testing, and inspection methods are not specified in other Sections, establish methods which will provide the
information required. Testing and verification required by this section shall be performed during the Commissioning
phase. Requirements in related Sections are independent from the requirements of this Section and shall not
be used to satisfy any of the requirements specified in this Section. Provide all materials, services, and labor
required to perform the pre- functional performance tests checks and functional performance tests. A functional
performance test shall be aborted if any system deficiency prevents the successful completion of the test or
if any participating non-Government commissioning team member of which participation is specified is not present
for the test.
3.2.1 Pre-Functional Performance Test Checklists
Perform Pre-Functional Performance Test Checklists for the items indicated in Appendix A. Correct and re-inspect
deficiencies discovered during these checks in accordance with the applicable contract requirements.
3.2.2 Functional Performance Tests
Perform Functional Performance Tests for the items indicated in Appendix B. Begin Functional Performance Tests
only after all Pre-Functional Performance Test Checklists have been successfully completed. Tests shall prove
all modes of the sequences of operation, and shall verify all other relevant contract requirements. Begin Tests
with equipment or components and progress through subsystems to complete systems. Upon failure of any Functional
Performance Test item, correct all deficiencies in accordance with the applicable contract requirements. The
item shall then be retested until it has been completed with no errors.
3.3 COMMISSIONING REPORT
The Commissioning Report shall consist of completed Pre- Functional Performance Test Checklists and completed
Functional Performance Tests organized by system and by subsystem and submitted as one package. The Commissioning
Report shall also include all HVAC systems test reports, inspection reports (Preparatory, Initial and Follow-up
inspections), start-up reports, TAB report, TAB verification report, Controls start-up test reports and Controls
Performance Verification Test (PVT) report. The results of failed tests shall be included along with a description
of the corrective action taken.
APPENDIX A
PRE-FUNCTIONAL PERFORMANCE TEST CHECKLISTS
Pre-Functional Performance Test Checklist - Multizone Air Handling Unit
For Air Handling Unit: [_____]
Checklist Item A M E T C O
Installation
a. Inspection and access doors are operable
and sealed. ___ ___ X ___ X ___
b. Condensate drainage is unobstructed.
(Visually verify pan drains completely by
pouring a cup of water into drain pan.) ___ ___ X X X ___
c. Fan belt adjusted. ___ ___ X ___ X ___
Electrical A M E T C O
a. Power available to unit disconnect. ___ X ___ X X ___
b. Power available to unit control panel. ___ X ___ X X ___
c. Proper motor rotation verified. ___ X ___ ___ X ___
d. Verify that power disconnect is located
within sight of the unit it controls. ___ X ___ X X ___
[e. Power available to electric heating coil. ___ X ___ X X ___ ]
Coils A M E T C O
[a. Chilled water piping properly connected. ___ ___ X X X ___ ]
[a. Refrigerant piping properly connected. ___ ___ X X X ___ ]
[b. Hot water piping properly connected. ___ ___ X X X ___ ]
[b. Steam and condensate piping properly
connected. ___ ___ X X X ___ ]
Controls A M E T C O
a. Control valves/actuators properly
installed. ___ X X X ___ ___
b. Control valves/actuators operable. ___ X X X ___ ___
c. O/A dampers/actuators properly installed. ___ X X X ___ ___
d. O/A dampers/actuators operable. ___ X X X ___ ___
Pre-Functional Performance Test Checklist - Multizone Air Handling Unit (cont)
A M E T C O
e. Zone dampers/actuators properly
installed & dampers leak checked. ___ X X X ___ ___
f. Zone dampers/actuators operable. ___ X X X ___ ___
Testing, Adjusting, and Balancing (TAB) A M E T C O
a. Construction filters removed and
replaced. ___ ___ X ___ X ___
b. TAB report approved. ___ X X ___ X
Pre-Functional Performance Test Checklist - Variable Volume Air Handling Unit
For Air Handling Unit: [_____]
Checklist Item A M E T C O
Installation
a. Inspection and access doors are operable
and sealed. ___ ___ X ___ X ___
b. Condensate drainage is unobstructed.
(Visually verify drainage by pouring a
cup of water into drain pan.) ___ ___ X X X ___
c. Fan belt adjusted. ___ ___ X ___ X ___
Electrical A M E T C O
a. Power available to unit disconnect. ___ X ___ X X ___
b. Power available to unit control panel. ___ X ___ X X ___
c. Proper motor rotation verified. ___ X ___ ___ X ___
d. Verify that power disconnect is located
within sight of the unit it controls. ___ X ___ X X ___
[e. Power available to electric heating coil. ___ X ___ X X ___]
Coils A M E T C O
[a. Chilled water piping properly connected. ___ ___ X X X ___]
[a. Refrigerant piping properly connected. ___ ___ X X X ___]
[b. Hot water piping properly connected. ___ ___ X X X ___]
[b. Steam and condensate piping properly
connected. ___ ___ X X X ___]
Pre-Functional Performance Test Checklist - Variable Volume Air Handling Unit
Controls A M E T C O
a. Control valves/actuators properly
installed. ___ X X X ___ ___
b. Control valves/actuators operable. ___ X X X ___ ___
c. Dampers/actuators properly installed. ___ X X X ___ ___
d. Dampers/actuators operable. ___ X X X ___ ___
e. Verify proper location, installation and
calibration of duct static pressure
sensor. ___ X X X ___ ___
f. Fan air volume controller operable. ___ X X X ___ ___
g. Air handler controls system operational. ___ X X X ___ ___
Testing, Adjusting, and Balancing (TAB) A M E T C O
a. Construction filters removed and
replaced. ___ ___ X ___ ___ ___
b. TAB report approved. ___ X X ___ X ___
Pre-Functional Performance Test Checklist - VAV Terminal
For VAV Terminal: [_____]
Checklist Item A M E T C O
Installation
[a. Reheat coil connected to hot water pipe. ___ ___ X ___ X ___]
[b. Electric reheat coil connected to local
disconnect. ___ X ___ ___ X ___]
Controls A M E T C O
a. Cooling only VAV terminal controls set. ___ X X X ___ ___
b. Cooling only VAV controls verified. ___ X X X ___ ___
c. Reheat VAV terminal controls set. ___ X X X ___ ___
d. Reheat terminal/coil controls verified. ___ X X X ___ ___
Testing, Adjusting, and Balancing (TAB) A M E T C O
a. TAB report approved. ___ ___ X ___ X ___
Pre-Functional Performance Test Checklist - DX Air Cooled Condensing Unit
For Condensing Unit: [_____]
Checklist Item A M E T C O
Installation
a. Check condenser fans for proper rotation. ___ ___ X ___ X ___
Electrical A M E T C O
a. Power available to unit disconnect. ___ X ___ X X ___
b. Power available to unit control panel. ___ X ___ X ___ ___
c. Verify that power disconnect is located
within sight of the unit it controls ___ X ___ X ___ ___
Controls A M E T C O
a. Unit safety/protection devices tested. ___ ___ X X ___ ___
b. Control system and interlocks installed. ___ ___ X X ___ ___
c. Control system and interlocks
operational. ___ ___ X X ___ ___
Pre-Functional Performance Test Checklist - Pumps
For Pump: [_____]
Checklist Item A M E T C O
Installation
a. Piping system installed. ___ ___ X X X ___
Electrical A M E T C O
a. Power available to pump disconnect. ___ X ___ X X ___
b. Pump rotation verified. ___ X ___ X X ___
c. Control system interlocks functional. ___ X ___ X ___ ___
Testing, Adjusting, and Balancing (TAB) A M E T C O
a. Pressure/temperature gauges installed. ___ ___ X ___ X ___
b. TAB Report approved. ___ ___ X ___ X ___
Pre-Functional Performance Test Checklist - Packaged Air Cooled Chiller
For Chiller: [_____]
Checklist Item A M E T C O
Installation
a. Chiller properly piped. ___ ___ X ___ ___ ___
Electrical A M E T C O
a. Power available to unit disconnect. ___ X ___ X ___ ___
b. Power available to unit control panel. ___ X ___ X ___ ___
c. Separate power is supplied to electric
heating tape. ___ X ___ X ___ ___
d. Verify that power disconnect is located
within sight of the unit it controls. ___ X ___ X ___ ___
Controls A M E T C O
a. Factory startup and checkout complete. ___ ___ X X ___ ___
b. Chiller safety/protection devices tested. ___ ___ X X ___ ___
c. Chilled water flow switch installed. ___ ___ X X ___ ___
d. Chilled water flow switch tested. ___ ___ X X ___ ___
e. Chilled water pump interlock installed. ___ ___ X X X ___
f. Chilled water pump interlock tested. ___ ___ ___ X
Pre-Functional Performance Test Checklist - Centrifugal Chiller
For Chiller: [_____]
Checklist Item
Installation A M E T C O
a. Chilled water connections properly piped. ___ ___ X ___ ___ ___
b. Condenser water connections properly ___ ___ X ___ ___ ___
piped
c. Refrigerant leak detector installed. ___ ___ ___ ___ ___ ___
[d. Oxygen sensor installed and tested. ___ ___ ___ ___ ___ ___]
e. Mechanical room ventilation installed as
specified. ___ ___ ___ ___ ___ ___
Electrical A M E T C O
a. Power available to unit starter. ___ X ___ X ___ ___
b. Power available to unit control panel. ___ X ___ X ___ ___
c. Verify that power disconnect is located
within sight of the unit it controls. ___ X ___ X ___ ___
Controls A M E T C O
a. Factory startup and checkout complete. ___ ___ X X ___ ___
b. Chiller safety/protection devices tested. ___ ___ ___ X ___ ___
c. Chilled water flow switch installed and
tested. ___ ___ X X ___ ___
e. Chilled water pump interlock installed
and tested. ___ ___ ___ X ___ ___
g. Condenser water flow switch installed
and tested. ___ ___ ___ X ___ ___
i. Condenser water pump interlock installed
and tested. ___ ___ ___ X ___ ___
Pre-Functional Performance Test Checklist - Cooling Tower
For Cooling Tower: [_____]
Checklist Item
Installation A M E T C O
a. Cooling tower properly piped. ___ ___ X X ___ ___
b. Cooling tower fan drive adjusted. ___ ___ ___ ___ X ___
c. Cooling tower makeup water supply piped. ___ ___ X X ___ ___
d. Verify makeup control valve shutoff. ___ ___ X ___ X ___
e. Fan lubricated and blade pitch adjusted. ___ ___ X ___ X ___
Electrical A M E T C O
a. Power available to tower disconnect. ___ X ___ X ___ ___
b. Power available to electric sump heater. ___ X ___ X ___ ___
c. Control system interlocks functional. ___ ___ ___ X ___ ___
d. Motor and fan rotation checked. ___ X ___ X ___ ___
e. Verify that power disconnect is located
within sight of the unit is controls. ___ X ___ X ___ ___
Piping A M E T C O
a. Condenser water treatment functional. ___ ___ X X X ___
b. All required temperature sensing wells,
pressure ports and flow sensors have
been installed for performance tests. ___ ___ ___ ___ ___ ___
Testing, Adjusting, and Balancing (TAB) A M E T C O
a. TAB report approved. ___ ___ X ___ X _____
Pre-Functional Performance Test Checklist - Hot Water Boiler
For Boiler: [_____]
Checklist Item
Installation A M E T C O
a. Boiler hot water piping installed. ___ ___ X ___ ___ ___
b. Boiler makeup water piping installed. ___ ___ X ___ ___ ___
c. Boiler fuel oil piping installed. ___ ___ X X X ___
d. Boiler gas piping installed. ___ ___ X X X ___
Startup A M E T C O
a. Boiler safety/protection devices,
including high temperature burner shut-off,
low water cutoff, flame failure, pre- and
post-purge, have been tested. ___ ___ ___ X ___ ___
b. Verify that PRV rating conforms to boiler
rating. ___ ___ ___ X ___ ___
c. Boiler water treatment system functional. ___ ___ X X ___ ___
d. Boiler startup and checkout complete. ___ ___ X X ___ ___
e. Combustion efficiency demonstrated. ___ ___ X ___ X ___
Electrical A M E T C O
a. Verify that power disconnect is located
within sight of the unit served. ___ X ___ X ___ ___
Controls A M E T C O
a. Hot water pump interlock installed
and tested. ___ ___ ___ X ___ ___
b. Hot water proof-of-flow switch
installed and tested ___ ___ X X ___ ___
c. Hot water heating controls operational. ___ ___ X X ___ ___
Testing, Adjusting, and Balancing (TAB) A M E T C O
a. TAB report approved. ___ ___ X ___ X ___
Pre-Functional Performance Test Checklist - Steam Boiler
For Boiler: [_____]
Checklist Item
Installation A M E T C O
a. Boiler steam piping installed. ___ ___ X X X ___
b. Boiler makeup water piping installed. ___ ___ X ___ X ___
c. Boiler fuel oil piping installed. ___ ___ X X X ___
d. Boiler gas piping installed. ___ ___ X X X ___
Startup A M E T C O
a. Boiler safety/protection devices,
including high temperature burner shut-
off, low water cutoff, flame failure,
pre and post purge, have been tested. ___ ___ ___ X ___ ___
b. Verify that PRV rating conforms to boiler
rating. ___ ___ ___ X ___ ___
c. Boiler feed water system operational. ___ ___ ___ X ___ ___
d. Boiler water treatment system functional. ___ ___ X X X ___
e. Boiler startup and checkout complete. ___ ___ ___ X ___ ___
f. All steam traps operational. ___ ___ X X X ___
g. All condensate return pumps operational. ___ ___ ___ ___ X ___
h. Combustion efficiency demonstrated. ___ ___ X ___ X ___
Electrical A M E T C O
a. Verify that power disconnect is located
within sight of the unit served. ___ X ___ X ___ ___
Testing, Adjusting, and Balancing (TAB) A M E T C O
a. TAB report approved. ___ ___ X ___ X ___
Pre-Functional Performance Test Checklist - Steam/Hot Water Converter
For Converter: [_____]
Checklist Item
Installation A M E T C O
a. Converter steam piping installed. ___ ___ X ___ X ___
b. Hot water piping installed. ___ ___ X ___ ___ ___
c. Makeup water piping installed. ___ ___ X X X ___
d. Vacuum breaker installed on shell of
shell and tube unit. ___ ___ X X X ___
Startup A M E T C O
a. All steam traps operational. ___ ___ X X X ___
b. All condensate return pumps operational. ___ ___ ___ X ___ ___
c. Converter safety/protection devices
tested. ___ ___ X X X ___
d. Converter startup and checkout complete. ___ ___ X X X ___
Controls A M E T C O
a. Control valves/actuators properly
installed. ___ ___ X ___ ___ ___
b. Control valves/actuators operable. ___ ___ X ___ ___ ___
Pre-Functional Performance Test Checklist - Fan Coil Unit
For Fan Coil Unit: [_____]
Checklist Item
Installation A M E T C O
a. Access doors/removable panels are operable
and sealed. ___ ___ X ___ X ___
b. Condensate drainage is unobstructed. ___ ___ X X X ___
c. Fan belt adjusted. ___ ___ X ___ X ___
Electrical A M E T C O
a. Power available to unit disconnect. ___ ___ ___ X ___ ___
b. Power available to unit control panel. ___ ___ ___ X ___ ___
c. Proper motor rotation verified. ___ ___ ___ ___ X ___
d. Verify that power disconnect is located
within sight of the unit it controls. ___ ___ ___ X ___ ___
[e. Power available to electric heating
coil. ___ ___ ___ X X ___]
Coils A M E T C O
[a. Dual temperature piping properly
connected. ___ ___ X ___ ___ ___]
[b. Chilled water piping properly connected. ___ ___ X X X ___]
[c. Hot water piping properly connected. ___ ___ X ___ ___ ___]
Controls A M E T C O
a. Control valves/actuators properly
installed. ___ ___ X ___ ___ ___
b. Control valves/actuators operable. ___ ___ X X ___ ___
c. Verify proper location and installation
of thermostat. ___ ___ X ___ ___ ___
Testing, Adjusting, and Balancing (TAB) A M E T C O
a. TAB Report approved. ___ ___ X ___ X ___
Pre-Functional Performance Test Checklist - Unit Heater
For Unit Heater: [_____]
Checklist Item
Installation A M E T C O
[a. Hot water piping properly connected. ___ ___ X ___ ___ ___]
[a. Steam and condensate piping properly
connected. ___ ___ X X X ___]
Electrical A M E T C O
a. Power available to unit disconnect. ___ ___ ___ X ___ ___
b. Proper motor rotation verified. ___ ___ ___ X X ___
c. Verify that power disconnect is located
within sight of the unit it controls. ___ ___ ___ X ___ ___
d. Power available to electric heating coil. ___ ___ ___ X ___ ___
Controls A M E T C O
a. Control valves properly installed. ___ ___ X ___ ___ ___
b. Control valves operable. ___ ___ X X ___ ___
c. Verify proper location and installation of
thermostat. ___ ___ X ___ ___ ___
Testing, Adjusting, and Balancing (TAB) A M E T C O
a. TAB Report approved. ___ ___ X ___ X ___
Pre-Functional Performance Test Checklist - Exhaust Fan
For Exhaust Fan: [_____]
Checklist Item
Installation A M E T C O
a. Fan belt adjusted. ___ ___ X ___ X ___
Electrical A M E T C O
a. Power available to fan disconnect. ___ ___ ___ X ___ ___
b. Proper motor rotation verified. ___ ___ ___ ___ X ___
c. Verify that power disconnect is located
within sight of the unit it controls. ___ ___ ___ X ___ ___
Controls A M E T C O
a. Control interlocks properly installed. ___ ___ ___ X ___ ___
b. Control interlocks operable. ___ ___ ___ X ___ ___
c. Dampers/actuators properly installed. ___ ___ X ___ ___ ___
d. Dampers/actuators operable. ___ ___ X ___ ___ ___
e. Verify proper location and installation of
thermostat. ___ ___ X ___ ___ ___
Testing, Adjusting, and Balancing (TAB) A M E T C O
a. TAB Report approved. ___ ___ X ___ X ___
Pre-Functional Performance Test Checklist - Computer Room Unit
For Computer Room Unit: [_____]
Checklist Item
Installation A M E T C O
a. Access doors are operable and sealed. ___ ___ X ___ X ___
b. Condensate drainage is unobstructed and
routed to floor drain. ___ ___ X X X ___
c. Fan belt adjusted. ___ ___ X ___ X ___
Electrical A M E T C O
a. Power available to unit disconnect. ___ X ___ X X ___
b. Proper motor rotation verified. ___ X ___ ___ X ___
c. Proper motor rotation verified. ___ X ___ ___ X ___
d. Verify that power disconnect is located
within sight of the unit it controls. ___ X ___ X ___ ___
[e. Power available to reheat coils. ___ X ___ ___ X ___]
Coils/Humidifier A M E T C O
[a. Chilled water piping properly connected. ___ ___ X ___ ___ ___]
[a. Refrigerant piping properly connected. ___ ___ X X X ___]
[b. Hot water piping properly connected. ___ ___ X ___ ___ ___]
[b. Steam piping properly connected. ___ ___ X X X ___]
[c. Humidifier makeup water connected. ___ ___ X X X ___]
Controls A M E T C O
a. Control valves operable. ___ ___ X X ___ ___
b. Unit control system operable and
verified. ___ ___ ___ X ___ ___
c. Verify proper location and installation of
thermostat. ___ ___ X ___ ___ ___
Testing, Adjusting, and Balancing (TAB) A M E T C O
a. TAB Report submitted. ___ ___ X ___ X ___
Pre-Functional Performance Test Checklist - HVAC System Controls
For HVAC System: [_____]
Checklist Item
Installation A M E T C O
a. Layout of control panel matches drawings. ___ ___ X X ___ ___
b. Framed instructions mounted in or near
control panel. ___ ___ X X ___ ___
c. Components properly labeled (on inside and
outside of panel). ___ ___ X X ___ ___
d. Control components piped and/or wired to
each labeled terminal strip. ___ ___ X X ___ ___
e. EMCS connection made to each labeled
terminal strip as shown. ___ ___ X X ___ ___
f. Control wiring and tubing labeled at all
terminations, splices, and junctions. ___ ___ X X ___ ___
Main Power and Control Air
a. 120 volt AC power available to panel. ___ ___ ___ X ___ ___
b. 138 kPa gauge20 psig
compressed air available to panel. ___ ___ X X ___ ___
Testing, Adjusting, and Balancing (TAB) A M E T C O
a. TAB Report submitted. ___ ___ X ___ X ___
Pre-Functional Performance Test Checklist - Single Zone Air Handling Unit
For Air Handling Unit: [_____]
Checklist Item
Installation A M E T C O
a. Inspection and access doors are operable
and sealed. ___ ___ X ___ X ___
b. Condensate drainage is unobstructed. ___ ___ X X X ___
c. Fan belt adjusted. ___ ___ X ___ X ___
Electrical A M E T C O
a. Power available to unit disconnect. ___ ___ ___ X X ___
b. Power available to unit control panel. ___ ___ ___ X ___ ___
c. Proper motor rotation verified. ___ ___ ___ ___ X ___
d. Verify that power disconnect is located
within sight of the unit it controls. ___ ___ ___ X ___ ___
e. Power available to electric heating coil. ___ ___ ___ X ___ ___
Coils A M E T C O
[a. Chilled water piping properly connected. ___ ___ X ___ ___ ___]
[a. Refrigerant piping properly connected. ___ ___ X X X ___]
[c. Hot water piping properly connected. ___ ___ X ___ ___ ___]
[c. Steam and condensate piping properly
connected. ___ ___ X X X ___]
Controls A M E T C O
a. Control valves/actuators properly
installed. ___ ___ X ___ ___ ___
b. Control valves/actuators operable. ___ ___ X ___ ___ ___
c. Dampers/actuators properly installed. ___ ___ X ___ ___ ___
d. Dampers/actuators operable. ___ ___ X ___ ___ ___
e. Verify proper location and installation
of thermostat. ___ ___ X ___ ___ ___
Testing, Adjusting, and Balancing (TAB) A M E T C O
a. TAB Report approved. ___ ___ X ___ X ___
Pre-Functional Performance Test Checklist - Energy Recovery System
For Energy Recovery System: [_____]
Checklist Item
Installation A M E T C O
a. Recovery system piping installed. ___ ___ X ___ X ___
Startup A M E T C O
a. Startup and checkout complete. ___ ___ X X X ___
Controls A M E T C O
a. Control valves/actuators properly
installed. ___ ___ X ___ ___ ___
b. Control valves/actuators operable. ___ ___ X ___ ___ ___
- End of Appendix A -
APPENDIX B
FUNCTIONAL PERFORMANCE TESTS CHECKLISTS
Functional Performance Test - Pump [_____]
NOTE: Prior to performing this test, for closed loop systems ensure that the system is pressurized and the
make-up water system is operational, or for open loop systems ensure that the sumps are filled to the proper level.
1. Activate pump start using control system commands.
a. Verify correct operation in:
HAND__________ OFF__________ AUTO__________
b. Verify pressure drop across strainer:
Strainer inlet pressure __________ kPa gaugepsig
Strainer outlet pressure _________ kPa gaugepsig
c. Verify pump inlet/outlet pressure reading, compare to Testing, Adjusting, and Balancing (TAB) Report and
pump design conditions.
DESIGN TAB ACTUAL
Pump inlet pressure kPa gaugepsig _________ __________ __________
Pump outlet pressure kPa gaugepsig _________ __________ __________
d. Operate pump at shutoff and at 100 percent of designed flow when all components are in full flow. Plot
test readings on pump curve and compare results against readings taken from flow measuring devices.
SHUTOFF 100 percent
Pump inlet pressure kPa gaugepsig __________ __________
Pump outlet pressure kPa gaugepsig __________ __________
Pump flow rate L/sgpm __________ __________
SETPOINT
Differential Pressure Transmitter ________
Functional Performance Test (cont) - Pump [_____]
e. For variable speed pumps, operate pump at shutoff (shutoff to be done in manual on var1able speed drive at
the minimum rpm that the system is being controlled at) and at minimum flow or when all components are in full
by-pass. Plot test readings on pump curve and compare results against readings taken from flow measuring devices.
SHUTOFF 100 percent
Pump inlet pressure kPa gaugepsig __________ __________
Pump outlet pressure kPa gaugepsig __________ __________
Pump flow rate L/sgpm __________ __________
SETPOINT
Differential Pressure Transmitter ________
2. Measure motor amperage each phase and voltage phase to phase and phase to ground for both the full flow
and the minimum flow conditions. Compare amperage to nameplate FLA
a. Full flow:
Nameplate FLA __________
Amperage Phase 1 __________ Phase 2__________ Phase 3__________
Voltage Ph1-Ph2 __________ Ph1-Ph3__________ Ph2-Ph3__________
Voltage Ph1-gnd __________ Ph2-gnd__________ Ph3-gnd__________
b. Minimum flow:
Amperage Phase 1 __________ Phase 2__________ Phase 3__________
Voltage Ph1-Ph2 __________ Ph1-Ph3__________ Ph2-Ph3__________
Voltage Ph1-gnd __________ Ph2-gnd__________ Ph3-gnd__________
3. Note unusual vibration, noise, etc.
___________________________________________________________________________
___________________________________________________________________________
Functional Performance Test (cont) - Pump [_____]
4. Certification: We the undersigned have witnessed the above functional performance tests and certify that
the item tested has met the performance requirements in this section of the specifications.
Signature and Date
Contractor's Commissioning Specialist _____________________________
Contractor's Mechanical Representative _____________________________
Contractor's Electrical Representative _____________________________
Contractor's TAB Representative _____________________________
Contractor's Controls Representative _____________________________
Contracting Officer's Representative _____________________________
Design Agency Representative _____________________________
Using Agency's Representative _____________________________
Functional Performance Test - Centrifugal Chiller [_____]
Note: If water-cooled chiller perform in conjunction with Cooling Tower test.
1. Demonstrate operation of chilled water system in accordance with specifications including the following:
Start building air handler to provide load for chiller. Activate controls system chiller start sequence as follows:
a. Time of day startup program initiates chiller start: ____________
b. Start condenser water pump and establish condenser water flow. Verify chiller condenser water proof-of-flow
switch operation._____
c. Start chilled water pump and establish chilled water flow. Verify chiller chilled water proof-of-flow
switch operation. ____________
d. Verify control system energizes chiller start sequence.__________
e. Verify chiller senses chilled water temperature above set point and control system activates chiller
start. _________________________
f. Verify functioning of "soft start" sequence. __________________
g. Record data in 2, 3 and 4 below on fully load chiller.
h. Shut off air handling equipment to remove load on chilled water system. Verify chiller shutdown sequence
is initiated and accomplished after load is removed. _____________________________
i. Restart air-handling equipment one minute after chiller shut down. Verify condenser water pump, cooling
tower, and chiller restart sequence. _________________________________________________________
2. Verify chiller inlet/outlet pressure and flow reading, compare to Testing, Adjusting, and Balancing (TAB)
Report, chiller design conditions, and chiller manufacturer's performance data.
DESIGN TAB REPORT ACTUAL
Chiller inlet pressure kPa gaugepsig __________ ____________________
Chiller outlet pressure kPa gaugepsig __________ ____________________
Chiller flow L/secGPM __________ __________ __________
3. Measure chiller amperage each phase and voltage phase to phase and phase to ground for both the fully loaded condition.
Motor F/L AMPS
Amperage Phase 1 __________ Phase 2__________ Phase 3_______ _________
Voltage Ph1-Ph2 __________ Ph1-Ph3__________ Ph2-Ph3_______
Voltage Ph1-gnd __________ Ph2-gnd__________ Ph3-gnd_______
Functional Performance Test (cont) - Centrifugal Chiller [_____]
4. a. Record the following information: Design
Ambient dry bulb temperature ___________ deg CF __________
Entering chilled water temperature _____ deg CF __________
Leaving chilled water temperature ______ deg CF __________
b. Calculate chiller load at ambient conditions and compare to chiller rated capacity from manufacturer's literature.
Calculated ________ KWsTon Rated ________ KWsTon.
5. Unusual vibration, noise, etc.
_______________________________________________________________________
_______________________________________________________________________
6. Certification: We the undersigned have witnessed the above functional performance tests and certify that
the item tested has met the performance requirements in this section of the specifications.
Signature and Date
Contractor's Commissioning Specialist _____________________________
Contractor's Mechanical Representative _____________________________
Contractor's Electrical Representative _____________________________
Contractor's TAB Representative _____________________________
Contractor's Controls Representative _____________________________
Contracting Officer's Representative _____________________________
Design Agency Representative _____________________________
Using Agency's Representative _____________________________
Functional Performance Test - Cooling Tower [_____]
1. Demonstrate operation of the cooling tower in accordance with specification and the following:
a. Activate cooling tower fan start using control system command. This should first start condenser water
pump, establish flow, delay fan start, as specified, to equalize flow in distribution basin and sump. Verify
fan start after timed delay._____________________________________
b. After chiller startup, control system should modulate bypass valve and two-speed fan motor to maintain
condenser water set point. Verify function of bypass valve under varying loads. __________________
c. Verify cooling tower interlock with chiller._____________________
d. Verify makeup water float valve is functioning. ___________________
e. Activate chemical treatment feed valve, verify makeup of chemical treatment system, pump, and controls.______________________________
f. Record the following:
Entering water temperature _____ deg CF
Leaving water temperature: _____ deg CF
Measured water flow: _____ L/sgpm
Entering air wet bulb temperature: _____ deg CF
2. Compare results with test results from cooling tower specification test.
3.
a. Stop all building cooling equipment so that cooling tower pumps stop. Observe tower for at least 15
minutes and verify no overflow occurs___________.
b. Start cooling tower pumps in hand and observe pumps for air binding/cavitation , none allowed __________.
4.Certification: We the undersigned have witnessed the above functional performance tests and certify that the
item tested has met the performance requirements in this section of the specifications.
Signature and Date
Contractor's Commissioning Specialist _____________________________
Contractor's Mechanical Representative _____________________________
Contractor's Electrical Representative _____________________________
Contractor's TAB Representative _____________________________
Contractor's Controls Representative _____________________________
Contracting Officer's Representative _____________________________
Design Agency Representative _____________________________
Using Agency's Representative _____________________________
Functional Performance Test Checklist - VAV Terminals
The Contracting officer will select VAV terminals to be spot-checked during the functional performance test.
The number of terminals selected shall not exceed 10 percent.
1. Functional Performance Test: Contractor shall demonstrate operation of selected VAV boxes in accordance
with specifications including the following:
a. Cooling only VAV boxes:
(1) Verify VAV box response to room temperature set point adjustment. Turn thermostat to 3 degrees C5 degrees
F below ambient and measure maximum airflow. Turn thermostat to 3 degrees C5 degrees F above ambient and measure
minimum airflow.
Setting Measured Design
Maximum flow [______] [_____] [_____] L/scfm
Minimum flow [______] [_____] [_____] L/scfm
b. Cooling with reheat VAV boxes:
(1) Verify VAV box response to room temperature set point adjustment. Turn thermostat to 3 degrees C5 degrees
F above ambient and measure maximum airflow. Turn thermostat to 3 degrees C5 degrees F below ambient and measure
minimum airflow.
Setting Measured Design
Maximum flow [______] [_____] [_____] L/scfm
Minimum flow [______] [_____] [_____] L/scfm
(2) Verify reheat coil operation range (full closed to full open) by turning room thermostat 3 degrees C5 degrees
F above ambient _______.
With heating water system and boiler in operation providing design supply hot water temperature record the following:
Design HW supply temperature______ deg CF
Actual HW supply temperature______ deg CF
AHU supply air temperature______ deg CF
VAV supply air temperature______ deg CF
Calculate coil capacity and compare to design:
Design ______ WBTU/hr Actual _____WBTU/hr
Functional Performance Test Checklist (cont)- VAV Terminals
c. Parallel Fan powered VAV boxes:
(1) Verify VAV box responses to call for heating via set point adjustment. Change from cooling set
point to heating set point. Verify cooling damper closes to minimum position, blower fan energizes according
to sequence of operation, and upon further drop in space temperature, heating coil activation. __________
With heating water system in operation providing design supply hot water temperature record the following:
Design HW supply temperature______ deg CF
Actual HW supply temperature______ deg CF
AHU supply air temperature______ deg CF
VAV supply air temperature______ deg CF
Calculate coil capacity and compare to design:
Design ______ WBTU/hr Actual _____WBTU/hr
(2) Check primary air damper maximum/minimum flow settings and compare to actual measured flows.
Setting Measured Design
Maximum flow [______] [_____] [_____] L/scfm
Minimum flow [______] [_____] [_____] L/scfm
(3) Check blower fan flow. [_____] L/scfm
(4) Verify free operation of fan backdraft damper (insure no primary air is being discharged into plenum space).
_____________________________________________________________________________
d. Series Fan Powered VAV boxes
(1) Ensure VAV fan starts prior to AHU fan
(2) Verify VAV box response to sensor call for heating via set point adjustment. Change from cooling set point
to heating set point. Verify cooling damper closes to minimum position and upon further drop in space temperature,
heating coil activation. With heating water system and boiler in operation providing design supply hot water
temperature record the following:
Design HW supply temperature______ deg CF
Actual HW supply temperature______ deg CF
AHU supply air temperature______ deg CF
VAV supply air temperature______ deg CF
Calculate coil capacity and compare to design:
Design ______ WBTU/hr Actual _____WBTU/hr
(3) Check primary air damper maximum/minimum flow settings and compare to actual measured flows.
Setting Measured Design
Maximum flow [______] [_____] [_____] L/scfm
Minimum flow [______] [_____] [_____] L/scfm
Functional Performance Test Checklist (cont)- VAV Terminals
(4) Verify that minimal primary air is discharging into the plenum space when in full cooling mode.
(5) Verify that no plenum air is being induced from the plenum space into the supply air during full cooling
by measuring supply air temperature and comparing to primary air temperature
Primary air temp _____ deg CF
Supply air temp _____ deg CF
2. Certification: We the undersigned have witnessed the above functional performance tests and certify that
the item tested has met the performance requirements in this section of the specifications.
Signature and Date
Contractor's Commissioning Specialist ___________________________
Contractor's Mechanical Representative _____________________________
Contractor's Electrical Representative _____________________________
Contractor's TAB Representative _____________________________
Contractor's Controls Representative _____________________________
Contracting Officer's Representative _____________________________
Design Agency Representative _____________________________
Using Agency's Representative _____________________________
Functional Performance Test Checklist - Variable Volume Air Handling Unit
For Air Handling Unit: [_____]
1. Functional Performance Test: Contractor shall verify operation of air handling unit in accordance with
specification including the following:
a. Ensure that a slight negative pressure exists on inboard side of the outside air dampers throughout the
operation of the dampers. Modulate OA, RA, and EA dampers from fully open to fully closed positions__________.
b. The following shall be verified [supply fan operating][supply and return fans operating] mode is initiated:
(1) All dampers in normal position prior to fan start___________.
(2) All valves in normal position prior to fan start____________.
(3) System safeties allow start if safety conditions are met.____
(4) VAV fan controller shall "soft-start" fan. __________________
(5) Modulate all VAV boxes to minimum air flow and verify that the static pressure does not exceed
the high static pressure shutdown setpoint_____________.
(6) Return all VAV boxes to auto _______________.
c. Occupied mode of operation - economizer de-energized.
(1) Outside air damper at minimum position. _____________________
(2) Return air damper open. _____________________________________
(3) Relief air damper [at minimum position] [closed]. ___________
(4) Chilled water control valve modulating to maintain leaving air temperature set point. Setpoint
_______deg CF Actual _____deg CF
(5) Fan VAV controller receiving signal from duct static pressure sensor and modulating fan to maintain
supply duct static pressure set point.
Setpoint _______kpainches-wg Actual _____kpainches-wg
d. Occupied mode of operation - economizer energized.
(1) Outside air damper modulated to maintain mixed air temperature set point. Setpoint _______deg
CF, Actual _____deg CF, Outside air damper position ________%.
(2) Relief air damper modulates with outside air damper according to sequence of operation. Relief
air damper position_____________%.
(3) Chilled water control valve modulating to maintain leaving air temperature set point. Setpoint
_______deg CF Actual _____deg CF
(4) Hot water control valve modulating to maintain leaving air temperature set point. Setpoint _______deg
CF Actual _____deg CF
Functional Performance Test Checklist (cont) - Variable Volume Air Handling Unit
(5) Fan VAV controller receives signal from duct static pressure sensor and modulates fan to maintain
supply duct static pressure set point. Setpoint kpainches-wg________________ Actual kpainches-wg___________
e. Unoccupied mode of operation
(1) Observe fan starts when space temperature calls for heating and/or cooling. _________ Note: This does not
apply to series boxes.
(2) All dampers in normal position. _____________________________
(3) Verify space temperature is maintained as specified in sequence of operation. _______________
f. The following shall be verified when the [supply fan off][supply and return fans off] mode is initiated:
(1) All dampers in normal position. _____________________________
(2) All valves in normal position. ______________________________
(3) Fan de-energizes. ___________________________________________
g. Verify the chilled water coil control valve operation by setting all VAV's to maximum and minimum cooling.
Max Cooling
Supply air temp. _____ deg CF Verify cooling valve operation_______.
Min cooling
Supply air temp. _____ deg CF Verify cooling valve operation_______.
h. Verify safety shut down initiated by low temperature protection thermostat. _________
i. Verify occupancy schedule is programmed into time clock/UMCS________.
2. Certification: We the undersigned have witnessed the above functional performance tests and certify that
the item tested has met the performance requirements in this section of the specifications.
Signature and Date
Contractor's Commissioning Specialist _____________________________
Contractor's Mechanical Representative _____________________________
Contractor's Electrical Representative _____________________________
Contractor's TAB Representative _____________________________
Contractor's Controls Representative _____________________________
Design Agency Representative _____________________________
Contracting Officer's Representative _____________________________
Using Agency's Representative _____________________________
Functional Performance Test Checklist - Single Zone Air Handling Unit
For Air Handling Unit: [_____]
1. Functional Performance Test: Contractor shall verify operation of air handling unit in accordance with
specification including the following:
a. Ensure that a slight negative pressure exists on inboard side of the outside air dampers throughout the
operation of the dampers. Modulate OA, RA, and EA dampers from fully open to fully closed positions.
a. The following shall be verified when the [supply fan operating] [supply and return fans operating]
mode is initiated:
(1) All dampers in normal position prior to fan start___________.
(2) All valves in normal position prior to fan start____________.
(3) System safeties allow start if safety conditions are met. ___
b. Occupied mode of operation - economizer de-energized.
(1) Outside air damper at minimum position.______________________
(2) Return air damper open.______________________________________
(3) Relief air damper [at minimum position][closed].____________
(4) Chilled water control valve modulating to maintain space cooling temperature set point. Setpoint
_______deg CF Actual _____deg CF
(5) Hot water control valve modulating to maintain space heating temperature set point input from outside
air temperature controller. ______
c. Occupied mode of operation - economizer energized.
(1) Outside air damper modulated to maintain mixed air temperature set point. Setpoint _______deg
CF Actual _____deg CF O/A damper position ___________% Return Air Temperature_____deg CF Outside Air Temperature
_______ deg CF
(2) Relief air damper modulates with outside air damper according to sequence of operation. Relief
air damper position ________%
(3) Chilled water control valve modulating to maintain space cooling temperature set point. Setpoint
_______deg CF Actual _____deg CF Return sensor overrides to normal operation.
d. Unoccupied mode of operation.
(1) Observe fan starts when space temperature calls for heating/cooling ____.
(2) All dampers in normal position. _________________________
(3) Verify low limit space temperature is maintained as specified in sequence of operation. ______________________________________
Functional Performance Test Checklist (cont) - Single Zone Air Handling Unit
e. The following shall be verified when the [supply fan off][supply and return fans off] mode is initiated:
(1) All dampers in normal position.______________________________
(2) All valves in normal position._______________________________
(3) Fan de-energizes. ___________________________________________
f. Verify cooling coil and heating coil operation by varying thermostat set point from cooling set point
to heating set point and returning to cooling set point________.
g. Verify safety shut down initiated by low temperature protection thermostat________.
h. Verify occupancy schedule is programmed into time clock/UMCS________.
2. Certification: We the undersigned have witnessed the above functional performance tests and certify that
the item tested has met the performance requirements in this section of the specifications.
Signature and Date
Contractor's Commissioning Specialist ____________________________
Contractor's Mechanical Representative _____________________________
Contractor's Electrical Representative _____________________________
Contractor's TAB Representative _____________________________
Contractor's Controls Representative _____________________________
Design Agency Representative _____________________________
Contracting Officer's Representative _____________________________
Using Agency's Representative _____________________________
Functional Performance Test Checklist - Multi-zone Air Handling Unit
For Air Handling Unit: [_____]
1. Functional Performance Test: Contractor shall verify operation of air handling unit in accordance with
specification including the following:
a. Ensure that a slight negative pressure exists on inboard side of the outside air dampers throughout
the operation of the dampers. Modulate OA, RA, and EA dampers from fully open to fully closed positions.
b. The following shall be verified when the supply and return fans operating mode is initiated:
(1) All dampers in normal position. _____________________________
(2) All valves in normal position. ______________________________
(3) System safeties allow start if safety conditions are met. ___
b. Occupied mode of operation - economizer de-energized.
(1) Outside air damper at minimum position. _____________________
(2) Return air damper open. _____________________________________
(3) Relief air damper [at minimum position] [closed]. ___________
(4) Chilled water control valve modulating to maintain cold deck supply air temperature set point.
Setpoint ______deg CF Actual _____deg CF
(5) Hot water control valve modulating to maintain hot deck supply air temperature set point input
from outside air temperature controller. Setpoint _______deg CF Actual _____deg CF O/A ________deg CF
c. Occupied mode of operation - economizer energized. Note outside air and return air temperature sensors
may need to be simulated.
(1) Outside air damper modulates to maintain mixed air temperature set point. Setpoint _______deg C
F Actual _____deg CF Return Air Temperature _______deg CF Outside Air Temperature _______deg CF
(2) Relief air damper modulates with outside air damper according to sequence of operation.__________________________________________________
(3)Chilled water control valve modulating to maintain cold deck supply air temperature set point. Setpoint
______deg CF Actual _____deg CF
(4)Hot water control valve modulating to maintain hot deck supply air temperature set point input from
outside air temperature controller. Setpoint _______deg CF Actual _____deg CF O/A ______ deg CF
Return temperature sensors to normal operation.
Functional Performance Test Checklist (cont) - Multi-zone Air Handling Unit
d. Unoccupied mode of operation note time clock and space temperature sensor may require simulation.
(4) Observe fan starts when space temperature calls for heating/cooling.
(5) All dampers in normal position. ___________________________
(6) Verify low limit space temperature is maintained as specified in sequence of operation. _____________________________________
e. The following shall be verified when the supply and return fans off mode is initiated:
(1) All dampers in normal position. ____________________________
(2) All valves in normal position. _____________________________
(3) Fan de-energizes. __________________________________________
Note: return time clock and space temperature sensors to normal operation.
f. Verify zone damper operation by varying zone thermostat set points from cooling set point to heating
set point and returning to cooling set point. ________________________________________________________________
g. Verify safety shut down initiated by low temperature protection thermostat. _____________________________________________________________
h. Index room thermostats to full cooling then to full heating. Measure and record cold deck, hot deck,
and supply air temperatures and determine damper leakage for a minimum of 2 zones.
Cold deck temperature __________ degrees CF
Hot deck temperature __________ degrees CF
Zone _______
Zone ____ Supply Air Temperature at Max Cooling _______deg CF
Zone ____ Supply Air Temperature at Max Heating _______deg CF
Zone ____Hot Deck Damper leakage at Max cooling _______l/SCFM
Zone ____Cold Deck Damper leakage at Max heating _______l/SCFM
Zone _______
Zone ____ Supply Air Temperature at Max Cooling _______deg CF
Zone ____ Supply Air Temperature at Max Heating _______deg CF
Zone ____Hot Deck Damper leakage at Max cooling _______l/SCFM
Zone ____Cold Deck Damper leakage at Max heating _______l/SCFM
i. Verify occupancy schedule is programmed into time clock/UMCS________.
Functional Performance Test Checklist (cont) - Multi-zone Air Handling Unit
2. Certification: We the undersigned have witnessed the above functional performance tests and certify that
the item tested has met the performance requirements in this section of the specifications.
Signature and Date
Contractor's Commissioning Specialist _____________________________
Contractor's Mechanical Representative _____________________________
Contractor's Electrical Representative _____________________________
Contractor's TAB Representative _____________________________
Contractor's Controls Representative _____________________________
Design Agency Representative _____________________________
Contracting Officer's Representative _____________________________
Using Agency's Representative _____________________________
Functional Performance Test Checklist - Packaged Air Cooled Chiller
For Chiller: [_____]
1. Functional Performance Test: Contractor shall demonstrate operation of chilled water system in accordance
with specifications including the following: Start building air handler to provide load for chiller. Activate
controls system chiller start sequence as follows.
a. Start chilled water pump and establish chilled water flow. Verify chiller-chilled water proof-of-flow
switch operation. ____________
b. Verify control system energizes chiller start sequence. ________
c. Verify chiller senses chilled water temperature above set point and control system activates chiller
start. Setpoint_____deg CF Actual_____ deg CF
d. Verify functioning of "soft start" sequence. ___________________
e. Verify and record chiller data in accordance with 2, 3 and 4 below on fully loaded chiller.
f. Shut off air handling equipment to remove load on chilled water system. Verify chiller shutdown sequence
is initiated and accomplished after load is removed. ___________________________________________
g. Restart air handling equipment one minute after chiller shut down. Verify chiller restart sequence. ________________________________
2. Verify chiller inlet/outlet pressure reading, compare to Testing, Adjusting, and Balancing (TAB) Report,
chiller design conditions, and chiller manufacturer's performance data.
DESIGN TAB TEST ACTUAL
Chiller inlet pressure (kPa gauge) __________ __________ __________
Chiller inlet pressure (psig) __________ __________ __________
Chiller outlet pressure (kPa gauge) __________ __________ __________
Chiller outlet pressure (psig) __________ __________ __________
Chiller flow L/secGPM __________ __________ __________
3. Verify chiller amperage each phase and voltage phase-to-phase and phase-to-ground.
Motor F/L AMPS
Amperage Phase 1 __________ Phase 2__________ Phase 3_______ _____
Voltage Ph1-Ph2 __________ Ph1-Ph3__________ Ph2-Ph3_______
Voltage Ph1-gnd __________ Ph2-gnd__________ Ph3-gnd_______
Functional Performance Test Checklist (cont) - Packaged Air Cooled Chiller
4.
a. Record the following information:
Design
Ambient dry bulb temperature ___________ degrees CF _____degrees CF
Entering chilled water temperature _____ degrees CF _____degrees CF
Leaving chilled water temperature ______ degrees CF _____degrees CF
b. Calculate chiller load at ambient conditions and compare to chiller rated capacity from manufacturer's
literature. Calculated ________ KWsTon Rated ________ KWsTon.
5. Unusual vibration, noise, etc.
___________________________________________________________________________
___________________________________________________________________________
6. Certification: We the undersigned have witnessed the above functional performance tests and certify that
the item tested has met the performance requirements in this section of the specifications.
Signature and Date
Contractor's Commissioning Specialist _____________________________
Contractor's Mechanical Representative _____________________________
Contractor's Electrical Representative _____________________________
Contractor's TAB Representative _____________________________
Contractor's Controls Representative _____________________________
Design Agency Representative _____________________________
Contracting Officer's Representative _____________________________
Using Agency's Representative _____________________________
Functional Performance Test Checklist - Air Cooled Condensing Unit
For Condensing Unit: [_____]
1. Functional Performance Test: Contractor shall demonstrate operation of refrigeration system in accordance
with specifications including the following: Start building air handler to provide load for condensing unit.
Activate controls system start sequence as follows.
a. Start air handling unit. Verify control system energizes condensing unit start sequence. __________________________________________
b. Verify and record data in 2 and 3 below.
c. Shut off air handling equipment to verify condensing unit de-energizes. ___________________________________________________________
d. Restart air handling equipment one minute after condensing unit shut down. Verify condensing unit
restart sequence. _____________________
2. Verify condensing unit amperage each phase and voltage phase to phase and phase to ground.
Motor Full-Load Amps __________
Amperage Phase 1 __________ Phase 2__________ Phase 3_______
Voltage Ph1-Ph2 __________ Ph1-Ph3__________ Ph2-Ph3_______
Voltage Ph1-gnd __________ Ph2-gnd__________ Ph3-gnd_______
3. Record the following information:
Ambient dry bulb temperature __________ degrees CF
Suction pressure __________ kPa gaugepsig
Discharge pressure __________ kPa gaugepsig
4. Unusual vibration, noise, etc.
___________________________________________________________________________
___________________________________________________________________________
5. Certification: We the undersigned have witnessed the above functional performance tests and certify that
the item tested has met the performance requirements in this section of the specifications.
Signature and Date
Contractor's Commissioning Specialist _____________________________
Contractor's Mechanical Representative _____________________________
Contractor's Electrical Representative _____________________________
Contractor's TAB Representative _____________________________
Contractor's Controls Representative _____________________________
Design Agency Representative _____________________________
Contracting Officer's Representative _____________________________
Using Agency's Representative _____________________________
Functional Performance Test Checklist - Hot Water Boiler
For Boiler: [_____]
1. Functional Performance Test: Contractor shall demonstrate operation of hot water system in accordance
with specifications including the following: Start building heating equipment to provide load for boiler. Activate
controls system boiler start sequence as follows.
a. Start hot water pump and establish hot water flow. Verify boiler hot water proof-of-flow switch operation. ____________________________
b. Verify control system energizes boiler start sequence. _________
c. Verify boiler senses hot water temperature below set point and control system activates boiler start.
Setpoint_________deg CF
2. Verify boiler inlet/outlet pressure reading, compare to Test and Balance (TAB) Report, boiler design conditions,
and boiler manufacturer's performance data.
DESIGN SYSTEM TEST ACTUAL
Boiler inlet water temperature deg CF __________ _________ _________
Boiler outlet water temperature deg CF __________ _________ _________
Boiler outlet pressure kPa gaugepsig __________ _________ _________
Boiler flow rate L/sgpm __________ _________ _________
Flue-gas temperature at boiler outlet deg CF _________ _________
Percent carbon dioxide in flue-gas _________ _________
Draft at boiler flue-gas exit kpainches-wg _________ _________
Stack emission pollutants concentration __________ _________ _________
Fuel type __________ _________ _________
Combustion efficiency __________ _________ _________
3. Record the following information:
Ambient dry bulb temperature to determine reset schedule_____degrees CF
Building Entering hot water temperature _____degrees CF
Building Leaving hot water temperature ____ degrees CF
4. Verify temperatures in item 3 are in accordance with the reset schedule. ______________________________________________________________
5. Verify proper operation of boiler safeties. ________________________
a. Low water_____
b. Water flow____
c. Flame failure____
d. Pilot failure____
e. Pre and Post Purge failure____
f. Pressure relief___
g. High temperature____
6. Shut off building heating equipment to remove load on hot water system. Verify boiler shutdown sequence
is initiated and accomplished after load is removed. _______________________________________________________
Functional Performance Test Checklist (cont) - Hot Water Boiler
7. Unusual vibration, noise, etc.
___________________________________________________________________________
___________________________________________________________________________
8. Certification: We the undersigned have witnessed the above functional performance tests and certify that
the item tested has met the performance requirements in this section of the specifications.
Signature and Date
Contractor's Commissioning Specialist _____________________________
Contractor's Mechanical Representative _____________________________
Contractor's Electrical Representative _____________________________
Contractor's TAB Representative _____________________________
Contractor's Controls Representative _____________________________
Design Agency Representative _____________________________
Contracting Officer's Representative _____________________________
Using Agency's Representative _____________________________
Functional Performance Test Checklist - Steam Boiler
For Boiler: [_____]
1. Functional Performance Test: Contractor shall demonstrate operation of steam heating system in accordance
with specifications including the following: Start building heating equipment to provide load for boiler. Activate
controls system boiler start sequence as follows.
a. Start steam heating system. Verify control system energizes boiler start sequence. __________________________________________________
b. Verify boiler senses steam pressure below set point and control system activates boiler start. __________________________________________
c. Shut off building heating equipment to remove load on steam heating system. Verify boiler shutdown
sequence is initiated and accomplished after load is removed. _____________________________________
d. Verify that water level and makeup water system are operational. _____________________________________________________________________________
2. Verify boiler inlet/outlet pressure reading, compare to boiler design conditions and manufacturer's performance data.
DESIGN SYSTEM TEST ACTUAL
Boiler inlet feedwater temp deg CF __________ __________ __________
Boiler outlet pressure kPa gaugepsig __________ __________ __________
Flue-gas temperature at boiler outlet deg CF __________ __________
Percent carbon dioxide in flue-gas __________ __________
Draft at boiler flue-gas exit kpainches-wg __________ __________
Stack emission pollutants concentration __________ __________ __________
Fuel type __________ __________ __________
Combustion efficiency __________ __________ __________
3. Record the following information:
Ambient temperature __________ deg CF
4. Verify proper operation of boiler safeties.__________________________
5. Unusual vibration, noise, etc.
___________________________________________________________________________
___________________________________________________________________________
6. Visually check refractory for cracks or spalling and refractory and tubes for flame impingement._______________________________________________
Functional Performance Test Checklist (cont) - Steam Boiler
7. Certification: We the undersigned have witnessed the above functional performance tests and certify that
the item tested has met the performance requirements in this section of the specifications.
Signature and Date
Contractor's Commissioning Specialist _____________________________
Contractor's Mechanical Representative _____________________________
Contractor's Electrical Representative _____________________________
Contractor's TAB Representative _____________________________
Contractor's Controls Representative _____________________________
Design Agency Representative _____________________________
Contracting Officer's Representative _____________________________
Using Agency's Representative _____________________________
Functional Performance Test Checklist - Fan Coil Units
The Contracting Officer will select fan coil units to be spot-checked during the functional performance test.
The number of terminals shall not exceed 10 percent. Hot water and chilled water systems must be in operation
providing design water temperatures.
1. Functional Performance Test: Contractor shall demonstrate operation of selected fan coils in accordance
with specifications including the following:
a. Cooling only fan coils:
(1) Verify fan coil unit response to room temp set point adjustment.
1. Check blower fan airflow. _____ L/scfm
2. Check cooling coil water flow. _____ L/sgpm
3. Verify proper operation of cooling water control valve.______
4. Cooling mode inlet air temperature ______deg CF
5. Cooling mode outlet air temperature______deg CF
6. Calculate coil sensible capacity and compare to design:
Calculated _______WattsBTU/hr Design______WattsBTU/hr
b. Cooling/heating fan coils:
(1) Verify fan coil unit response to room temp set point adjustment.
1. Check blower fan airflow. _____ L/scfm
2. Check cooling coil water flow. _____ L/sgpm
3. Verify proper operation of cooling water control valve. ____
4. Check cooling mode inlet air temperature. _____deg CF
5. Check cooling mode outlet air temperature. _____deg CF
6. Calculate cooling coil sensible capacity and compare to design:
7. Calculated _________WattsBTU/hr Design_____WattsBTU/hr
8. Check heating coil water flow. _____ L/sgpm
9. Verify proper operation of heating water control valve. _____
10. Check heating mode inlet air temperature. _____ deg CF
11. Check heating mode outlet air temperature. _____deg CF
12. Calculate heating coil capacity and compare to design:
Calculated______WattsBTU/hr design_______WattsBTU/hr
2. Certification: We the undersigned have witnessed the above functional performance tests and certify that
the item tested has met the performance requirements in this section of the specifications.
Signature and Date
Contractor's Commissioning Specialist ____________________________
Contractor's Mechanical Representative _____________________________
Contractor's Electrical Representative ______________________________
Contractor's TAB Representative ______________________________
Contractor's Controls Representative _____________________________
Design Agency Representative _____________________________
Contracting Officer's Representative _____________________________
Using Agency's Representative _____________________________
Functional Performance Test Checklist - Unit Heaters
The Contracting Officer will select unit heaters to be spot-checked during the functional performance test.
The number of terminals shall not exceed 10 percent. Hot water systems {for hot water unit heaters} must be in
operation and supplying design hot water supply temperature water.
1. Functional Performance Test: Contractor shall demonstrate operation of selected unit heaters:
a. Verify unit heater response to room temperature set point adjustment.___________________________________
b. Check heating mode inlet air temperature. _____ deg CF
c. Check heating mode outlet air temperature. _____ deg CF
d. Record manufacturer's submitted fan capacity _____L/scfm
e. Calculate unit heater capacity using manufacturer's fan capacity and recorded temperatures and compare
to design.
f. Calculated_____WattsBTU/hr Design______WattsBTU/hr
2. Certification: We the undersigned have witnessed the above functional performance tests and certify that
the item tested has met the performance requirements in this section of the specifications.
Signature and Date
Contractor's Commissioning Specialist _____________________________
Contractor's Mechanical Representative _____________________________
Contractor's Electrical Representative _____________________________
Contractor's TAB Representative _____________________________
Contractor's Controls Representative _____________________________
Design Agency Representative _____________________________
Contracting Officer's Representative _____________________________
Using Agency's Representative _____________________________
Functional Performance Test Checklist - Steam/Hot Water Converter
For Converter: [_____]
1. Functional Performance Test: Contractor shall demonstrate operation of heating system in accordance with
specifications including the following: Start building heating equipment to provide load for converter.
a. Verify control system energizes. _______________________________
b. Verify converter senses hot water temperature below set point and control system modulates steam valve. ____________________________________
c. Shut off building heating equipment to remove load on heating system. Verify converter steam valve
closes after load is removed. ______
2. Verify converter inlet/outlet pressure reading, compare to converter design conditions and manufacturer's
performance data.
DESIGN ACTUAL
Converter inlet water temp deg CF __________ __________
Converter outlet water temp deg CF __________ __________
Converter inlet steam pressure kpapsig __________ __________
Determine water flow rate based
on pressure drop through converter (L/SGPM)__________ __________
Determine water flow rate with flow
measuring device L/SGPM __________ __________
Verify that temperature of water Current Actual
is in accordance with outdoor air Setpoint Temperature
reset schedule __________ __________
3. Verify proper operation of converter safeties. _____________________
4. Check and report unusual vibration, noise, etc.
___________________________________________________________________________
___________________________________________________________________________
5. Certification: We the undersigned have witnessed the above functional performance tests and certify that
the item tested has met the performance requirements in this section of the specifications.
Signature and Date
Contractor's Commissioning Specialist ____________________________
Contractor's Mechanical Representative _____________________________
Contractor's Electrical Representative _____________________________
Contractor's TAB Representative _____________________________
Contractor's Controls Representative _____________________________
Design Agency Representative _____________________________
Contracting Officer's Representative _____________________________
Using Agency's Representative _____________________________
Functional Performance Test Checklist - Computer Room Unit
For Computer Room Unit: [_____]
1. Functional Performance Test: Contractor shall verify operation of computer room unit in accordance with
specification including the following:
a. System safeties allow start if safety conditions are met. ______
b. Verify cooling and heating operation by varying thermostat set point from space set point to space
set point plus 5.510 degrees, space set point minus 5.510 degrees, and returning to space set point. ________________
c. Verify humidifier operation by varying humidistat set point from space set point to space set point
plus 20 percent RH, and returning to space set point. _________________________________________________________________
d. Verify that airflow is within tolerance specified in Section 23 05 93 TESTING, ADJUSTING, AND BALANCING
OF HVAC SYSTEMS. _____________________________________________________________________________
2. Certification: We the undersigned have witnessed the above functional performance tests and certify that
the item tested has met the performance requirements in this section of the specifications.
Signature and Date
Contractor's Commissioning Specialist ____________________________
Contractor's Mechanical Representative _____________________________
Contractor's Electrical Representative _____________________________
Contractor's TAB Representative _____________________________
Contractor's Controls Representative _____________________________
Design Agency Representative _____________________________
Contracting Officer's Representative _____________________________
Using Agency's Representative _____________________________
Functional Performance Test Checklist - HVAC Controls
For HVAC System: [_____]
The Contracting Officer will select HVAC control systems to undergo functional performance testing. The number
of systems shall not exceed 10 percent. Perform this test simultaneously with FPT for AHU or other controlled equipment.
1. Functional Performance Test: Contractor shall verify operation of HVAC controls by performing the Performance
Verification Test {PVT} test for that system. Contractor to provide blank PVT test procedures previously done
by the controls Contractor.
2. Verify interlock with UMCS system______.
3. Verify all required I/O points function from the UMCS system_____.
4. Certification: We the undersigned have witnessed the Performance Verification Test and certify that
the item tested has met the performance requirements in this section of the specifications.
Signature and Date
Contractor's Commissioning Specialist _________________________
Contractor's Mechanical Representative ___________________________
Contractor's Electrical Representative ___________________________
Contractor's TAB Representative ___________________________
Contractor's Controls Representative ___________________________
Design Agency Representative ___________________________
Contractor's Officer's Representative ___________________________
Using Agency's Representative ___________________________
Functional Performance Test Checklist - Energy Recovery System
For Energy Recovery System: [_____]
1. Functional Performance Test: Contractor shall demonstrate operation of energy recovery system in accordance
with specifications including the following: Start equipment to provide energy source for recovery system.
a. Verify energy source is providing recoverable energy.____________
b. Verify recovery system senses available energy and activates.____
2. Verify recovery system inlet/outlet readings, compare to design conditions and manufacturer's performance data.
Design Actual
Primary loop inlet temp (degrees CF) __________ __________
Primary loop outlet temp (degrees CF) __________ __________
Primary loop flow rate L/s[gpm][cfm] __________ __________
Secondary loop inlet temp (degrees CF) __________ __________
Secondary loop outlet temp (degrees CF) __________ __________
Secondary loop flow rate L/s[gpm][cfm] __________ __________
Primary loop energy WattsBTU/hr __________ __________
Secondary loop energy WattsBTU/hr __________ __________
3. Verify that recovery system deactivates when recoverable energy is no longer available. __________________________________________________
4. Check and report unusual vibration, noise, etc. ___________________________________________________________________________
___________________________________________________________________________
5. Certification: We the undersigned have witnessed the above functional performance tests and certify that
the item tested has met the performance requirements in this section of the specifications.
Signature and Date
Contractor's Commissioning Specialist __________________________
Contractor's Mechanical Representative ___________________________
Contractor's Electrical Representative ___________________________
Contractor's TAB Representative ___________________________
Contractor's Controls Representative ___________________________
Design Agency Representative __________________________
Contractor's Officer's Representative ___________________________
Using Agency's Representative ___________________________
- End of Appendix B -
-End of document